[X9D] Small font added
[X9D] Main view continued [Sky9x] Sounds selection again OK (thanks Scott for the report)
This commit is contained in:
bsongis
+47
-396
@@ -37,11 +37,6 @@ uint8_t displayBuf[DISPLAY_W*DISPLAY_H/8];
|
||||
#define DISPLAY_END (displayBuf+sizeof(displayBuf))
|
||||
#define ASSERT_IN_DISPLAY(p) assert((p) >= displayBuf && (p) < DISPLAY_END)
|
||||
|
||||
#ifdef SIMU
|
||||
bool lcd_refresh = true;
|
||||
uint8_t lcd_buf[DISPLAY_W*DISPLAY_H/8];
|
||||
#endif
|
||||
|
||||
void lcd_clear()
|
||||
{
|
||||
memset(displayBuf, 0, sizeof(displayBuf));
|
||||
@@ -66,11 +61,6 @@ void lcd_img(xcoord_t x, uint8_t y, const pm_uchar * img, uint8_t idx, uint8_t m
|
||||
|
||||
uint8_t lcdLastPos;
|
||||
|
||||
#if defined(PCBSKY9X)
|
||||
uint8_t lcdLock;
|
||||
uint32_t lcdInputs;
|
||||
#endif
|
||||
|
||||
void lcd_putcAtt(xcoord_t x, uint8_t y, const unsigned char c, LcdFlags mode)
|
||||
{
|
||||
uint8_t *p = &displayBuf[ y / 8 * DISPLAY_W + x ];
|
||||
@@ -124,9 +114,9 @@ void lcd_putcAtt(xcoord_t x, uint8_t y, const unsigned char c, LcdFlags mode)
|
||||
* by ten bottom bytes (20 bytes per * char) */
|
||||
q = &font_8x10[((uint16_t)c-0x20)*16];
|
||||
for (int8_t i=9; i>=0; i--) {
|
||||
// TODO? if (mode & CONDENSED && i<=1) break;
|
||||
uint8_t b1=0, b2=0;
|
||||
if (i!=0 && i!= 9) {
|
||||
if (mode & CONDENSED && i<=1) break;
|
||||
if (i!=0 && i!=9) {
|
||||
b1 = pgm_read_byte(q++); /*top byte*/
|
||||
b2 = pgm_read_byte(q++); /*top byte*/
|
||||
}
|
||||
@@ -154,6 +144,26 @@ void lcd_putcAtt(xcoord_t x, uint8_t y, const unsigned char c, LcdFlags mode)
|
||||
}
|
||||
}
|
||||
}
|
||||
else if (mode & SMLSIZE) {
|
||||
q = &font_4x6[((uint16_t)c-0x20)*5+4];
|
||||
uint8_t ym8 = (y % 8);
|
||||
p += 4;
|
||||
for (int8_t i=4; i>=0; i--) {
|
||||
uint8_t b = pgm_read_byte(q--);
|
||||
if (inv) b = ~b & 0x7f;
|
||||
|
||||
if (p<DISPLAY_END) {
|
||||
ASSERT_IN_DISPLAY(p);
|
||||
*p = (*p & (~(0x7f << ym8))) + (b << ym8);
|
||||
if (ym8) {
|
||||
uint8_t *r = p + DISPLAY_W;
|
||||
if (r<DISPLAY_END)
|
||||
*r = (*r & (~(0x7f >> (8-ym8)))) + (b >> (8-ym8));
|
||||
}
|
||||
}
|
||||
p--;
|
||||
}
|
||||
}
|
||||
#endif
|
||||
else {
|
||||
uint8_t condense=0;
|
||||
@@ -230,6 +240,7 @@ void lcd_putsnAtt(xcoord_t x, uint8_t y, const pm_char * s, uint8_t len, LcdFlag
|
||||
x += FW;
|
||||
if (mode&DBLSIZE) x += FW-1;
|
||||
else if (mode&MIDSIZE) x += FW-3;
|
||||
else if (mode&SMLSIZE) x -= 1;
|
||||
}
|
||||
else {
|
||||
x += (c*FW/2);
|
||||
@@ -316,7 +327,8 @@ void lcd_outdezNAtt(xcoord_t x, uint8_t y, int16_t val, LcdFlags flags, uint8_t
|
||||
fw += FWNUM;
|
||||
}
|
||||
else if (midsize) {
|
||||
fw += FWNUM-1;
|
||||
flags |= CONDENSED;
|
||||
fw += FWNUM-2;
|
||||
}
|
||||
else {
|
||||
if (flags & LEFT) {
|
||||
@@ -542,14 +554,22 @@ void putsTime(xcoord_t x, uint8_t y, putstime_t tme, LcdFlags att, LcdFlags att2
|
||||
|
||||
qr = div(tme, 60);
|
||||
|
||||
#if defined(PCBSKY9X)
|
||||
#if defined(PCBX9D)
|
||||
if (att & MIDSIZE) {
|
||||
div_t qr2 = div(qr.quot, 60);
|
||||
LCD_2DOTS(x+2*8-5, y, att);
|
||||
lcd_outdezNAtt(x, y, qr2.quot, att|LEADING0|LEFT, 2);
|
||||
x += 2*8+2;
|
||||
}
|
||||
#define separator ':'
|
||||
#elif defined(PCBSKY9X)
|
||||
char separator = ':';
|
||||
if (tme >= 3600 && (~att & DBLSIZE)) {
|
||||
qr = div(qr.quot, 60);
|
||||
lcd_outdezAtt(x+2*FWNUM, y, qr.quot, att);
|
||||
lcd_putcAtt(lcdLastPos-((att & DBLSIZE) ? 1 : 0), y, 'h', att&att2);
|
||||
lcd_outdezNAtt(lcdLastPos+FW, y, qr.rem, att2|LEADING0|LEFT, 2);
|
||||
return;
|
||||
separator = 'h';
|
||||
}
|
||||
#else
|
||||
#define separator ':'
|
||||
#endif
|
||||
|
||||
uint8_t x2, x3;
|
||||
@@ -558,15 +578,21 @@ void putsTime(xcoord_t x, uint8_t y, putstime_t tme, LcdFlags att, LcdFlags att2
|
||||
x3 = x+2*(FW+FWNUM)+FW-2;
|
||||
}
|
||||
else if (att&MIDSIZE) {
|
||||
x2 = x+2*8-1;
|
||||
x3 = x+2*8+7;
|
||||
x2 = x+2*8-5;
|
||||
x3 = x+2*8+2;
|
||||
}
|
||||
else {
|
||||
x2 = x+2*FWNUM-1;
|
||||
x3 = x+2*FWNUM-1+FW;
|
||||
}
|
||||
|
||||
lcd_putcAtt(x2, y, ':', att&att2);
|
||||
#if defined(PCBX9D)
|
||||
if (att&MIDSIZE) {
|
||||
LCD_2DOTS(x2, y, att);
|
||||
}
|
||||
else
|
||||
#endif
|
||||
lcd_putcAtt(x2, y, separator, att&att2);
|
||||
lcd_outdezNAtt(x, y, qr.quot, att|LEADING0|LEFT, 2);
|
||||
lcd_outdezNAtt(x3, y, qr.rem, att2|LEADING0|LEFT, 2);
|
||||
}
|
||||
@@ -748,381 +774,6 @@ void putsRotaryEncoderMode(xcoord_t x, uint8_t y, uint8_t phase, uint8_t idx, Lc
|
||||
}
|
||||
#endif
|
||||
|
||||
#ifdef PCBSKY9X
|
||||
|
||||
// LCD i/o pins
|
||||
// LCD_RES PC27
|
||||
// LCD_CS1 PC26
|
||||
// LCD_E PC12
|
||||
// LCD_RnW PC13
|
||||
// LCD_A0 PC15
|
||||
// LCD_D0 PC0
|
||||
// LCD_D1 PC7
|
||||
// LCD_D2 PC6
|
||||
// LCD_D3 PC5
|
||||
// LCD_D4 PC4
|
||||
// LCD_D5 PC3
|
||||
// LCD_D6 PC2
|
||||
// LCD_D7 PC1
|
||||
|
||||
#define LCD_DATA 0x000000FFL
|
||||
#ifdef REVB
|
||||
#define LCD_A0 0x00000080L
|
||||
#else
|
||||
#define LCD_A0 0x00008000L
|
||||
#endif
|
||||
#define LCD_RnW 0x00002000L
|
||||
#define LCD_E 0x00001000L
|
||||
#define LCD_CS1 0x04000000L
|
||||
#define LCD_RES 0x08000000L
|
||||
|
||||
// Lookup table for prototype board
|
||||
#ifndef REVB
|
||||
const uint8_t Lcd_lookup[] =
|
||||
{
|
||||
0x00,0x01,0x80,0x81,0x40,0x41,0xC0,0xC1,0x20,0x21,0xA0,0xA1,0x60,0x61,0xE0,0xE1,
|
||||
0x10,0x11,0x90,0x91,0x50,0x51,0xD0,0xD1,0x30,0x31,0xB0,0xB1,0x70,0x71,0xF0,0xF1,
|
||||
0x08,0x09,0x88,0x89,0x48,0x49,0xC8,0xC9,0x28,0x29,0xA8,0xA9,0x68,0x69,0xE8,0xE9,
|
||||
0x18,0x19,0x98,0x99,0x58,0x59,0xD8,0xD9,0x38,0x39,0xB8,0xB9,0x78,0x79,0xF8,0xF9,
|
||||
0x04,0x05,0x84,0x85,0x44,0x45,0xC4,0xC5,0x24,0x25,0xA4,0xA5,0x64,0x65,0xE4,0xE5,
|
||||
0x14,0x15,0x94,0x95,0x54,0x55,0xD4,0xD5,0x34,0x35,0xB4,0xB5,0x74,0x75,0xF4,0xF5,
|
||||
0x0C,0x0D,0x8C,0x8D,0x4C,0x4D,0xCC,0xCD,0x2C,0x2D,0xAC,0xAD,0x6C,0x6D,0xEC,0xED,
|
||||
0x1C,0x1D,0x9C,0x9D,0x5C,0x5D,0xDC,0xDD,0x3C,0x3D,0xBC,0xBD,0x7C,0x7D,0xFC,0xFD,
|
||||
0x02,0x03,0x82,0x83,0x42,0x43,0xC2,0xC3,0x22,0x23,0xA2,0xA3,0x62,0x63,0xE2,0xE3,
|
||||
0x12,0x13,0x92,0x93,0x52,0x53,0xD2,0xD3,0x32,0x33,0xB2,0xB3,0x72,0x73,0xF2,0xF3,
|
||||
0x0A,0x0B,0x8A,0x8B,0x4A,0x4B,0xCA,0xCB,0x2A,0x2B,0xAA,0xAB,0x6A,0x6B,0xEA,0xEB,
|
||||
0x1A,0x1B,0x9A,0x9B,0x5A,0x5B,0xDA,0xDB,0x3A,0x3B,0xBA,0xBB,0x7A,0x7B,0xFA,0xFB,
|
||||
0x06,0x07,0x86,0x87,0x46,0x47,0xC6,0xC7,0x26,0x27,0xA6,0xA7,0x66,0x67,0xE6,0xE7,
|
||||
0x16,0x17,0x96,0x97,0x56,0x57,0xD6,0xD7,0x36,0x37,0xB6,0xB7,0x76,0x77,0xF6,0xF7,
|
||||
0x0E,0x0F,0x8E,0x8F,0x4E,0x4F,0xCE,0xCF,0x2E,0x2F,0xAE,0xAF,0x6E,0x6F,0xEE,0xEF,
|
||||
0x1E,0x1F,0x9E,0x9F,0x5E,0x5F,0xDE,0xDF,0x3E,0x3F,0xBE,0xBF,0x7E,0x7F,0xFE,0xFF
|
||||
} ;
|
||||
#endif
|
||||
|
||||
void lcdSendCtl(uint8_t val)
|
||||
{
|
||||
register Pio *pioptr ;
|
||||
// register uint32_t x ;
|
||||
|
||||
#ifdef REVB
|
||||
pioptr = PIOC ;
|
||||
pioptr->PIO_CODR = LCD_CS1 ; // Select LCD
|
||||
PIOA->PIO_CODR = LCD_A0 ;
|
||||
pioptr->PIO_CODR = LCD_RnW ; // Write
|
||||
pioptr->PIO_ODSR = val ;
|
||||
#else
|
||||
pioptr = PIOC ;
|
||||
pioptr->PIO_CODR = LCD_CS1 ; // Select LCD
|
||||
pioptr->PIO_CODR = LCD_A0 ; // Control
|
||||
pioptr->PIO_CODR = LCD_RnW ; // Write
|
||||
pioptr->PIO_ODSR = Lcd_lookup[val] ;
|
||||
#endif
|
||||
|
||||
pioptr->PIO_SODR = LCD_E ; // Start E pulse
|
||||
// Need a delay here (250nS)
|
||||
TC0->TC_CHANNEL[0].TC_CCR = 5 ; // Enable clock and trigger it (may only need trigger)
|
||||
while ( TC0->TC_CHANNEL[0].TC_CV < 9 ) // Value depends on MCK/2 (used 18MHz)
|
||||
{
|
||||
// Wait
|
||||
}
|
||||
pioptr->PIO_CODR = LCD_E ; // End E pulse
|
||||
#ifdef REVB
|
||||
PIOA->PIO_SODR = LCD_A0 ; // Data
|
||||
#else
|
||||
pioptr->PIO_SODR = LCD_A0 ; // Data
|
||||
#endif
|
||||
pioptr->PIO_SODR = LCD_CS1 ; // Deselect LCD
|
||||
}
|
||||
|
||||
void lcd_init()
|
||||
{
|
||||
register Pio *pioptr ;
|
||||
// /home/thus/txt/datasheets/lcd/KS0713.pdf
|
||||
// ~/txt/flieger/ST7565RV17.pdf from http://www.glyn.de/content.asp?wdid=132&sid=
|
||||
|
||||
#ifdef REVB
|
||||
configure_pins( LCD_A0, PIN_ENABLE | PIN_LOW | PIN_OUTPUT | PIN_PORTA | PIN_NO_PULLUP ) ;
|
||||
pioptr = PIOC ;
|
||||
pioptr->PIO_PER = 0x0C0030FFL ; // Enable bits 27,26,13,12,7-0
|
||||
pioptr->PIO_CODR = LCD_E | LCD_RnW ;
|
||||
pioptr->PIO_SODR = LCD_RES | LCD_CS1 ;
|
||||
pioptr->PIO_OER = 0x0C0030FFL ; // Set bits 27,26,13,12,7-0 output
|
||||
pioptr->PIO_OWER = 0x000000FFL ; // Allow write to ls 8 bits in ODSR
|
||||
#else
|
||||
pioptr = PIOC ;
|
||||
pioptr->PIO_PER = 0x0C00B0FFL ; // Enable bits 27,26,15,13,12,7-0
|
||||
pioptr->PIO_CODR = LCD_E | LCD_RnW | LCD_A0 ;
|
||||
pioptr->PIO_SODR = LCD_RES | LCD_CS1 ;
|
||||
pioptr->PIO_OER = 0x0C00B0FFL ; // Set bits 27,26,15,13,12,7-0 output
|
||||
pioptr->PIO_OWER = 0x000000FFL ; // Allow write to ls 8 bits in ODSR
|
||||
#endif
|
||||
|
||||
pioptr->PIO_CODR = LCD_RES ; // Reset LCD
|
||||
TC0->TC_CHANNEL[0].TC_CCR = 5 ; // Enable clock and trigger it (may only need trigger)
|
||||
while ( TC0->TC_CHANNEL[0].TC_CV < 200 ) // > 10us, Value depends on MCK/2 (used 18MHz)
|
||||
{
|
||||
// Wait
|
||||
}
|
||||
pioptr->PIO_SODR = LCD_RES ; // Remove LCD reset
|
||||
TC0->TC_CHANNEL[0].TC_CCR = 5 ; // Enable clock and trigger it (may only need trigger)
|
||||
while ( TC0->TC_CHANNEL[0].TC_CV < 27000 ) // 1500us, Value depends on MCK/2 (used 18MHz)
|
||||
{
|
||||
// Wait
|
||||
}
|
||||
lcdSendCtl(0xe2); //Initialize the internal functions
|
||||
lcdSendCtl(0xae); //DON = 0: display OFF
|
||||
lcdSendCtl(0xa1); //ADC = 1: reverse direction(SEG132->SEG1)
|
||||
lcdSendCtl(0xA6); //REV = 0: non-reverse display
|
||||
lcdSendCtl(0xA4); //EON = 0: normal display. non-entire
|
||||
lcdSendCtl(0xA2); // Select LCD bias=0
|
||||
lcdSendCtl(0xC0); //SHL = 0: normal direction (COM1->COM64)
|
||||
lcdSendCtl(0x2F); //Control power circuit operation VC=VR=VF=1
|
||||
lcdSendCtl(0x25); //Select int resistance ratio R2 R1 R0 =5
|
||||
lcdSendCtl(0x81); //Set reference voltage Mode
|
||||
lcdSendCtl(0x22); // 24 SV5 SV4 SV3 SV2 SV1 SV0 = 0x18
|
||||
lcdSendCtl(0xAF); //DON = 1: display ON
|
||||
// g_eeGeneral.contrast = 0x22;
|
||||
|
||||
#ifdef REVB
|
||||
pioptr->PIO_ODR = 0x0000003AL ; // Set bits 1, 3, 4, 5 input
|
||||
pioptr->PIO_PUER = 0x0000003AL ; // Set bits 1, 3, 4, 5 with pullups
|
||||
pioptr->PIO_ODSR = 0 ; // Drive D0 low
|
||||
#else
|
||||
pioptr->PIO_ODR = 0x0000003CL ; // Set bits 2, 3, 4, 5 input
|
||||
pioptr->PIO_PUER = 0x0000003CL ; // Set bits 2, 3, 4, 5 with pullups
|
||||
pioptr->PIO_ODSR = 0 ; // Drive D0 low
|
||||
#endif
|
||||
}
|
||||
|
||||
void lcdSetRefVolt(uint8_t val)
|
||||
{
|
||||
#ifndef SIMU
|
||||
register Pio *pioptr ;
|
||||
pioptr = PIOC ;
|
||||
|
||||
// read the inputs, and lock the LCD lines
|
||||
lcdInputs = PIOC->PIO_PDSR; // 6 LEFT, 5 RIGHT, 4 DOWN, 3 UP ()
|
||||
lcdLock = 1 ;
|
||||
|
||||
pioptr->PIO_OER = 0x0C00B0FFL ; // Set bits 27,26,15,13,12,7-0 output
|
||||
|
||||
lcdSendCtl(0x81);
|
||||
if ( val == 0 )
|
||||
{
|
||||
val = 0x22 ;
|
||||
}
|
||||
lcdSendCtl(val);
|
||||
|
||||
#ifdef REVB
|
||||
pioptr->PIO_ODR = 0x0000003AL ; // Set bits 1, 3, 4, 5 input
|
||||
pioptr->PIO_PUER = 0x0000003AL ; // Set bits 1, 3, 4, 5 with pullups
|
||||
#else
|
||||
pioptr->PIO_ODR = 0x0000003CL ; // Set bits 2, 3, 4, 5 input
|
||||
pioptr->PIO_PUER = 0x0000003CL ; // Set bits 2, 3, 4, 5 with pullups
|
||||
#endif
|
||||
|
||||
pioptr->PIO_ODSR = lcdInputs; // Drive D0 low
|
||||
lcdLock = 0 ;
|
||||
#endif
|
||||
}
|
||||
|
||||
#ifndef SIMU
|
||||
void refreshDisplay()
|
||||
{
|
||||
register Pio *pioptr;
|
||||
register uint8_t *p = displayBuf;
|
||||
register uint32_t y;
|
||||
register uint32_t x;
|
||||
register uint32_t z;
|
||||
register uint32_t ebit;
|
||||
#ifndef REVB
|
||||
register uint8_t *lookup;
|
||||
lookup = (uint8_t *) Lcd_lookup;
|
||||
#endif
|
||||
|
||||
ebit = LCD_E;
|
||||
|
||||
#ifdef REVB
|
||||
pioptr = PIOA;
|
||||
pioptr->PIO_PER = 0x00000080; // Enable bit 7 (LCD-A0)
|
||||
pioptr->PIO_OER = 0x00000080;// Set bit 7 output
|
||||
#endif
|
||||
|
||||
// read the inputs, and lock the LCD lines
|
||||
lcdInputs = PIOC->PIO_PDSR; // 6 LEFT, 5 RIGHT, 4 DOWN, 3 UP ()
|
||||
lcdLock = 1 ;
|
||||
|
||||
pioptr = PIOC;
|
||||
#ifdef REVB
|
||||
pioptr->PIO_OER = 0x0C0030FFL; // Set bits 27,26,15,13,12,7-0 output
|
||||
#else
|
||||
pioptr->PIO_OER = 0x0C00B0FFL; // Set bits 27,26,15,13,12,7-0 output
|
||||
#endif
|
||||
for (y = 0; y < 8; y++) {
|
||||
lcdSendCtl(g_eeGeneral.optrexDisplay ? 0 : 0x04);
|
||||
lcdSendCtl(0x10); //column addr 0
|
||||
lcdSendCtl(y | 0xB0); //page addr y
|
||||
|
||||
pioptr->PIO_CODR = LCD_CS1; // Select LCD
|
||||
PIOA->PIO_SODR = LCD_A0; // Data
|
||||
pioptr->PIO_CODR = LCD_RnW; // Write
|
||||
|
||||
#ifdef REVB
|
||||
x = *p;
|
||||
#else
|
||||
x = lookup[*p];
|
||||
#endif
|
||||
for (z = 0; z < DISPLAY_W; z += 1) {
|
||||
|
||||
// The following 7 lines replaces by a lookup table
|
||||
// x = __RBIT( *p++ ) ;
|
||||
// x >>= 23 ;
|
||||
// if ( x & 0x00000100 )
|
||||
// {
|
||||
// x |= 1 ;
|
||||
// }
|
||||
// pioptr->PIO_ODSR = x ;
|
||||
|
||||
pioptr->PIO_ODSR = x;
|
||||
pioptr->PIO_SODR = ebit; // Start E pulse
|
||||
// Need a delay here (250nS)
|
||||
p += 1;
|
||||
#ifdef REVB
|
||||
x = *p;
|
||||
#else
|
||||
x = lookup[*p];
|
||||
#endif
|
||||
// TC0->TC_CHANNEL[0].TC_CCR = 5 ; // Enable clock and trigger it (may only need trigger)
|
||||
// while ( TC0->TC_CHANNEL[0].TC_CV < 3 ) // Value depends on MCK/2 (used 6MHz)
|
||||
// {
|
||||
// // Wait
|
||||
// }
|
||||
pioptr->PIO_CODR = ebit; // End E pulse
|
||||
}
|
||||
pioptr->PIO_SODR = LCD_CS1; // Deselect LCD
|
||||
}
|
||||
|
||||
pioptr->PIO_ODSR = 0xFF ; // Drive lines high
|
||||
#ifdef REVB
|
||||
pioptr->PIO_PUER = 0x0000003AL ; // Set bits 1, 3, 4, 5 with pullups
|
||||
pioptr->PIO_ODR = 0x0000003AL ; // Set bits 1, 3, 4, 5 input
|
||||
#else
|
||||
pioptr->PIO_PUER = 0x0000003CL ; // Set bits 2, 3, 4, 5 with pullups
|
||||
pioptr->PIO_ODR = 0x0000003CL ; // Set bits 2, 3, 4, 5 input
|
||||
#endif
|
||||
|
||||
pioptr->PIO_ODSR = lcdInputs; // Drive D0 low
|
||||
lcdLock = 0;
|
||||
}
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
||||
#define delay_1us() _delay_us(1)
|
||||
void delay_1_5us(int ms)
|
||||
{
|
||||
for(int i=0; i<ms; i++) delay_1us();
|
||||
}
|
||||
|
||||
void lcdSendCtl(uint8_t val)
|
||||
{
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_CS1);
|
||||
#ifdef LCD_MULTIPLEX
|
||||
DDRA = 0xFF; // set LCD_DAT pins to output
|
||||
#endif
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_A0);
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_RnW);
|
||||
PORTA_LCD_DAT = val;
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_E);
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_E);
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_A0);
|
||||
#ifdef LCD_MULTIPLEX
|
||||
DDRA = 0x00; // set LCD_DAT pins to input
|
||||
#endif
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_CS1);
|
||||
}
|
||||
|
||||
#if defined(PCBSTD) && defined(VOICE)
|
||||
volatile uint8_t LcdLock ;
|
||||
#define LCD_LOCK() LcdLock = 1
|
||||
#define LCD_UNLOCK() LcdLock = 0
|
||||
#else
|
||||
#define LCD_LOCK()
|
||||
#define LCD_UNLOCK()
|
||||
#endif
|
||||
|
||||
inline void lcd_init()
|
||||
{
|
||||
// /home/thus/txt/datasheets/lcd/KS0713.pdf
|
||||
// ~/txt/flieger/ST7565RV17.pdf from http://www.glyn.de/content.asp?wdid=132&sid=
|
||||
|
||||
LCD_LOCK();
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_RES); //LCD_RES
|
||||
delay_1us();
|
||||
delay_1us();// f520 call 0xf4ce delay_1us() ; 0x0xf4ce
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_RES); // f524 sbi 0x15, 2 IOADR-PORTC_LCD_CTRL; 21 1
|
||||
delay_1_5us(1500);
|
||||
lcdSendCtl(0xe2); //Initialize the internal functions
|
||||
lcdSendCtl(0xae); //DON = 0: display OFF
|
||||
lcdSendCtl(0xa1); //ADC = 1: reverse direction(SEG132->SEG1)
|
||||
lcdSendCtl(0xA6); //REV = 0: non-reverse display
|
||||
lcdSendCtl(0xA4); //EON = 0: normal display. non-entire
|
||||
lcdSendCtl(0xA2); // Select LCD bias=0
|
||||
lcdSendCtl(0xC0); //SHL = 0: normal direction (COM1->COM64)
|
||||
lcdSendCtl(0x2F); //Control power circuit operation VC=VR=VF=1
|
||||
lcdSendCtl(0x25); //Select int resistance ratio R2 R1 R0 =5
|
||||
lcdSendCtl(0x81); //Set reference voltage Mode
|
||||
lcdSendCtl(0x22); // 24 SV5 SV4 SV3 SV2 SV1 SV0 = 0x18
|
||||
lcdSendCtl(0xAF); //DON = 1: display ON
|
||||
g_eeGeneral.contrast = 0x22;
|
||||
LCD_UNLOCK();
|
||||
}
|
||||
|
||||
void lcdSetRefVolt(uint8_t val)
|
||||
{
|
||||
LCD_LOCK();
|
||||
lcdSendCtl(0x81);
|
||||
lcdSendCtl(val);
|
||||
LCD_UNLOCK();
|
||||
}
|
||||
|
||||
#ifndef SIMU
|
||||
void refreshDisplay()
|
||||
{
|
||||
LCD_LOCK();
|
||||
uint8_t *p=displayBuf;
|
||||
for(uint8_t y=0; y < 8; y++) {
|
||||
lcdSendCtl(0x04);
|
||||
lcdSendCtl(0x10); //column addr 0
|
||||
lcdSendCtl( y | 0xB0); //page addr y
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_CS1);
|
||||
#ifdef LCD_MULTIPLEX
|
||||
DDRA = 0xFF; // set LCD_DAT pins to output
|
||||
#endif
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_A0);
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_RnW);
|
||||
for (xcoord_t x=DISPLAY_W; x>0; --x) {
|
||||
PORTA_LCD_DAT = *p++;
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_E);
|
||||
PORTC_LCD_CTRL &= ~(1<<OUT_C_LCD_E);
|
||||
}
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_A0);
|
||||
PORTC_LCD_CTRL |= (1<<OUT_C_LCD_CS1);
|
||||
}
|
||||
LCD_UNLOCK();
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
#ifdef SIMU
|
||||
void refreshDisplay()
|
||||
{
|
||||
memcpy(lcd_buf, displayBuf, sizeof(displayBuf));
|
||||
lcd_refresh = true;
|
||||
}
|
||||
#endif
|
||||
|
||||
void lcdSetContrast()
|
||||
{
|
||||
lcdSetRefVolt(g_eeGeneral.contrast);
|
||||
|
||||
Reference in New Issue
Block a user