feat: Support for ext. Multiplex MLink JR type module (#3352)
* introducing external MLink module telemetry as module PPM subtype * implemented fix for sensor discovery display not showing all detected sensors (is in separate PR too) implemented PPM subtypes in Companion * add PPM subtype to model printer finalize subtypes for PPM in Companion * added logic to try to use HW UART with inverters turned off first (e.g. NV14), then, if not successfull use soft serial inverted (== uninverted data due to HW inverters on PCB) changed start bit detection IRQ priority from 5 to the previous 0 (also in separate PR) * extended telemetry timeout to 2s due to slow Mlink RSSI update rate * changed the "NOTLM" sub-type texts to: - "No Telem" for 128x64 (this is the max numbers of characters it can take) - "No Telemetry" everything else including Companion * Companion: - lower case 1st charachter on PpmSubTypeStrings to ppmSubTypeStrings - added telemetry hooks for ppmSubTypeStrings stringx * simplified serial port initialization for MLink telemetry * editorial change: corrected obsolete comment
This commit is contained in:
@@ -35,14 +35,34 @@ enum {
|
||||
MLINK_CAPACITY = 11,
|
||||
MLINK_FLOW = 12,
|
||||
MLINK_DISTANCE = 13,
|
||||
MLINK_GRATE = 14,
|
||||
MLINK_RX_VOLTAGE = 16, // out of range ID for specific RxBt treatment
|
||||
MLINK_LOSS = 17, // out of range ID for handling number of loss
|
||||
MLINK_TX_RSSI = 18, // out of range ID for handling Telemetry RSSi reported by multi
|
||||
MLINK_TX_LQI = 19, // out of range ID for handling Telemetry LQI reported by multi
|
||||
MLINK_SPECIAL = 20, // out of raneg ID fro handling special value class
|
||||
};
|
||||
|
||||
void processMLinkTelemetryData(uint8_t data, uint8_t* rxBuffer, uint8_t& rxBufferCount);
|
||||
#define MLINK_SVC 0 // ID speial value class - can't use in enum as indexes have to start at 0
|
||||
|
||||
void mlinkSetDefault(int index, uint16_t id, uint8_t subId, uint8_t instance);
|
||||
|
||||
// Used by multi protocol
|
||||
void processMLinkPacket(const uint8_t *packet);
|
||||
void processMLinkPacket(const uint8_t *packet, bool multi);
|
||||
|
||||
// used by telemetry driver
|
||||
#define MSB_EXT_MODULE_PACKET_LEN 18 // packet length minus start and stop byte
|
||||
#define MSB_STX 0x02 // start byte
|
||||
#define MSB_ETX 0x03 // stop byte
|
||||
#define MSB_STUFF_ESC 0x1B // ESC symbol
|
||||
#define MSB_STUFF_OFFSET 0x20 // byte stuffing offset
|
||||
#define MSB_VALID_TELEMETRY 0x13
|
||||
#define MSB_NORMAL 0x06
|
||||
#define MSB_NORMAL_FAST 0x04
|
||||
#define MSB_RANGE 0x46
|
||||
#define MSB_RANGE_FAST 0x44
|
||||
|
||||
// used by external MLink module driver
|
||||
#define PPM_MSB_BAUDRATE 115200
|
||||
|
||||
void processExternalMLinkSerialData(void* ctx, uint8_t data, uint8_t* buffer, uint8_t* len);
|
||||
|
||||
Reference in New Issue
Block a user