docs: flysky st16 touchscreen modification (#7528)
|
After Width: | Height: | Size: 69 KiB |
|
After Width: | Height: | Size: 223 KiB |
|
After Width: | Height: | Size: 154 KiB |
|
After Width: | Height: | Size: 231 KiB |
|
After Width: | Height: | Size: 272 KiB |
|
After Width: | Height: | Size: 311 KiB |
|
After Width: | Height: | Size: 185 KiB |
|
After Width: | Height: | Size: 120 KiB |
|
After Width: | Height: | Size: 169 KiB |
|
After Width: | Height: | Size: 222 KiB |
|
After Width: | Height: | Size: 67 KiB |
|
After Width: | Height: | Size: 161 KiB |
|
After Width: | Height: | Size: 159 KiB |
|
After Width: | Height: | Size: 95 KiB |
|
After Width: | Height: | Size: 81 KiB |
|
After Width: | Height: | Size: 222 KiB |
@@ -0,0 +1,93 @@
|
|||||||
|
# Flysky ST16 Hardware Mod for Complete touch Support
|
||||||
|
|
||||||
|
This touch screen modification can only be used under the edgetx system and cannot be applied to the flyskyos system.
|
||||||
|
|
||||||
|
Adding a touch screen will occupy the wiring of the two rear buttons, thereby affecting the functionality of those two buttons.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Back_of_st16.png)
|
||||||
|
|
||||||
|
relevant document:[flysky ST16 touch](https://www.jianguoyun.com/p/DfgUegMQys6vDhir-aUGIAA)
|
||||||
|
|
||||||
|
- [line link](#line-link)
|
||||||
|
- [Screen material preparation](#screen-material-preparation)
|
||||||
|
- [Touchscreen assembly](#touchscreen-assembly)
|
||||||
|
|
||||||
|
## line link
|
||||||
|
Connect as shown in the picture.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Contact_connection.png)
|
||||||
|
|
||||||
|
I use 0.8mm thick PCB for connection.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/PCB.png)
|
||||||
|
## Screen material preparation
|
||||||
|
|
||||||
|
Separate the original outer screen from the inner screen
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Screen_separation.png)
|
||||||
|
|
||||||
|
Replace with the IC:ft6236U touch external screen.
|
||||||
|
|
||||||
|
Product link:[FT6236U touch glass](https://item.taobao.com/item.htm?from=cart&id=627131226350&mi_id=0000tXbR3mX7zBJlOkPorNzXzd14FBHPjWwk2tTlrs-2qR8&skuId=4449085013858&spm=a1z0d.6639537%2F202410.item.d627131226350.2eed7484BfaY5i&upStreamPrice=1800)
|
||||||
|
|
||||||
|
Handling the touch glass
|
||||||
|
|
||||||
|
Remove the inner protective film and the double-sided adhesive.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Touching_the_glass_treatment.png)
|
||||||
|
|
||||||
|
Cut off the protruding part of the front protective film and keep the protective film intact.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Touching_the_glass_treatment_2.png)
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Wire_connection.png)
|
||||||
|
|
||||||
|
Display screen 1-6 pin:
|
||||||
|
1-GND
|
||||||
|
2-RST
|
||||||
|
3-INT
|
||||||
|
4-SCL
|
||||||
|
5-SDA
|
||||||
|
6-VCC
|
||||||
|
The touch screen is connected to the display's 1-6 pins via 6-pin connector.
|
||||||
|
|
||||||
|
Welding 6-pin and 40-pin connectors.
|
||||||
|
|
||||||
|
40pin connector, 0.5mm pitch, with the cover attached below
|
||||||
|
|
||||||
|
6pin connector, 0.5mm pitch, upper connection
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/FPC.png)
|
||||||
|
## Touchscreen assembly
|
||||||
|
|
||||||
|
The materials required for screen assembly
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Screen_assembly_components.png)
|
||||||
|
|
||||||
|
Place the inner screen inside the screen frame, and have the wires pass through the gap.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Screen_installation.png)
|
||||||
|
|
||||||
|
Then place the touch glass outside the screen frame, and have the wiring pass through the gap.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Touching_glass_installation.png)
|
||||||
|
|
||||||
|
As shown in the picture, open the touch glass. Clean the inner screen and the inner side of the touch glass. Put in the TPU gasket.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Install_the_TPU_gasket.png)
|
||||||
|
|
||||||
|
Fasten the screen cover plate
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Top_cover_installation.png)
|
||||||
|
|
||||||
|
Connect the 6-pin touch cable to the FPC cable, and then connect the 40-pin cable.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/FPC_connection.png)
|
||||||
|
|
||||||
|
Use tape to fix the fpc to the back of the outer frame.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/Placement_of_FPC.png)
|
||||||
|
|
||||||
|
Put the screen assembly back into the remote control and insert the screws to connect the wires.
|
||||||
|
|
||||||
|
[](../assets/images/hw/flysky-st16/FPC_connector_module.png)
|
||||||
@@ -83,6 +83,7 @@ nav:
|
|||||||
- Hardware Mods:
|
- Hardware Mods:
|
||||||
- Flysky Hall Sticks: mods/flysky-hall-sticks.md
|
- Flysky Hall Sticks: mods/flysky-hall-sticks.md
|
||||||
- Flysky FRM303 Mod for TX16S: mods/flysky-frm303-tx16s.md
|
- Flysky FRM303 Mod for TX16S: mods/flysky-frm303-tx16s.md
|
||||||
|
- Flysky ST16 Touch Support: mods/flysky-st16-touch-support.md
|
||||||
- Flysky PL18 & PL18EV: mods/flysky-pl18.md
|
- Flysky PL18 & PL18EV: mods/flysky-pl18.md
|
||||||
- Flysky NB4+: mods/flysky-nb4plus.md
|
- Flysky NB4+: mods/flysky-nb4plus.md
|
||||||
- Flashing EdgeTX to Flysky PL18/Paladin-EV: mods/flashing-flysky-pl18.md
|
- Flashing EdgeTX to Flysky PL18/Paladin-EV: mods/flashing-flysky-pl18.md
|
||||||
|
|||||||