Files
edgetx-gx12/radio/src/targets/horus/usb_conf.h
T

165 lines
6.6 KiB
C

/*
* Copyright (C) OpenTX
*
* Based on code named
* th9x - http://code.google.com/p/th9x
* er9x - http://code.google.com/p/er9x
* gruvin9x - http://code.google.com/p/gruvin9x
*
* License GPLv2: http://www.gnu.org/licenses/gpl-2.0.html
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef _USB_CONF_H_
#define _USB_CONF_H_
#include "STM32F4xx_DSP_StdPeriph_Lib_V1.4.0/Libraries/CMSIS/Device/ST/STM32F4xx/Include/stm32f4xx.h"
/* USB Core and PHY interface configuration.
Tip: To avoid modifying these defines each time you need to change the USB
configuration, you can declare the needed define in your toolchain
compiler preprocessor.
*/
/****************** USB OTG FS PHY CONFIGURATION *******************************
* The USB OTG FS Core supports one on-chip Full Speed PHY.
*
* The USE_EMBEDDED_PHY symbol is defined in the project compiler preprocessor
* when FS core is used.
*******************************************************************************/
#ifndef USE_USB_OTG_FS
#define USE_USB_OTG_FS // USB2.0 Full Speed == 12 Mbit
#endif /* USE_USB_OTG_FS */
#ifdef USE_USB_OTG_FS
#define USB_OTG_FS_CORE
#endif
/*******************************************************************************
* FIFO Size Configuration in Device mode
*
* (i) Receive data FIFO size = RAM for setup packets +
* OUT endpoint control information +
* data OUT packets + miscellaneous
* Space = ONE 32-bits words
* --> RAM for setup packets = 10 spaces
* (n is the nbr of CTRL EPs the device core supports)
* --> OUT EP CTRL info = 1 space
* (one space for status information written to the FIFO along with each
* received packet)
* --> data OUT packets = (Largest Packet Size / 4) + 1 spaces
* (MINIMUM to receive packets)
* --> OR data OUT packets = at least 2*(Largest Packet Size / 4) + 1 spaces
* (if high-bandwidth EP is enabled or multiple isochronous EPs)
* --> miscellaneous = 1 space per OUT EP
* (one space for transfer complete status information also pushed to the
* FIFO with each endpoint's last packet)
*
* (ii)MINIMUM RAM space required for each IN EP Tx FIFO = MAX packet size for
* that particular IN EP. More space allocated in the IN EP Tx FIFO results
* in a better performance on the USB and can hide latencies on the AHB.
*
* (iii) TXn min size = 16 words. (n : Transmit FIFO index)
* (iv) When a TxFIFO is not used, the Configuration should be as follows:
* case 1 : n > m and Txn is not used (n,m : Transmit FIFO indexes)
* --> Txm can use the space allocated for Txn.
* case2 : n < m and Txn is not used (n,m : Transmit FIFO indexes)
* --> Txn should be configured with the minimum space of 16 words
* (v) The FIFO is used optimally when used TxFIFOs are allocated in the top
* of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones.
* (vi) In HS case12 FIFO locations should be reserved for internal DMA registers
* so total FIFO size should be 1012 Only instead of 1024
*******************************************************************************/
/****************** USB OTG FS CONFIGURATION **********************************/
#ifdef USB_OTG_FS_CORE
#define RX_FIFO_FS_SIZE 128
#define TX0_FIFO_FS_SIZE 64
#define TX1_FIFO_FS_SIZE 128
#define TX2_FIFO_FS_SIZE 0
#define TX3_FIFO_FS_SIZE 0
// #define USB_OTG_FS_LOW_PWR_MGMT_SUPPORT
// #define USB_OTG_FS_SOF_OUTPUT_ENABLED
#endif
/****************** USB OTG MISC CONFIGURATION ********************************/
#define VBUS_SENSING_ENABLED
/****************** USB OTG MODE CONFIGURATION ********************************/
//#define USE_HOST_MODE
#define USE_DEVICE_MODE
//#define USE_OTG_MODE
#ifndef USB_OTG_FS_CORE
#ifndef USB_OTG_HS_CORE
#error "USB_OTG_HS_CORE or USB_OTG_FS_CORE should be defined"
#endif
#endif
#ifndef USE_DEVICE_MODE
#ifndef USE_HOST_MODE
#error "USE_DEVICE_MODE or USE_HOST_MODE should be defined"
#endif
#endif
#ifndef USE_USB_OTG_HS
#ifndef USE_USB_OTG_FS
#error "USE_USB_OTG_HS or USE_USB_OTG_FS should be defined"
#endif
#else //USE_USB_OTG_HS
#ifndef USE_ULPI_PHY
#ifndef USE_EMBEDDED_PHY
#error "USE_ULPI_PHY or USE_EMBEDDED_PHY should be defined"
#endif
#endif
#endif
/****************** C Compilers dependant keywords ****************************/
/* In HS mode and when the DMA is used, all variables and data structures dealing
with the DMA during the transaction process should be 4-bytes aligned */
#ifdef USB_OTG_HS_INTERNAL_DMA_ENABLED
#if defined (__GNUC__) /* GNU Compiler */
#define __ALIGN_END __attribute__ ((aligned (4)))
#define __ALIGN_BEGIN
#else
#define __ALIGN_END
#if defined (__CC_ARM) /* ARM Compiler */
#define __ALIGN_BEGIN __align(4)
#elif defined (__ICCARM__) /* IAR Compiler */
#define __ALIGN_BEGIN
#elif defined (__TASKING__) /* TASKING Compiler */
#define __ALIGN_BEGIN __align(4)
#endif /* __CC_ARM */
#endif /* __GNUC__ */
#else
#define __ALIGN_BEGIN
#define __ALIGN_END
#endif /* USB_OTG_HS_INTERNAL_DMA_ENABLED */
/* __packed keyword used to decrease the data type alignment to 1-byte */
#if !defined(__packed)
#if defined (__CC_ARM) /* ARM Compiler */
#define __packed __packed
#elif defined (__ICCARM__) /* IAR Compiler */
#define __packed __packed
#elif defined ( __GNUC__ ) /* GNU Compiler */
#define __packed __attribute__ ((__packed__))
#elif defined (__TASKING__) /* TASKING Compiler */
#define __packed __unaligned
#endif /* __CC_ARM */
#endif
#endif // _USB_CONF_H_
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/