Files
edgetx-gx12/radio/src/targets/sky9x/board.cpp
T
reichiandBertrand Songis 0ebf9dbb1e Fix ar9x compile/boot (#7102)
* view_main: fix compile on atsam

* AR9X: fix broken/missing boardInit() since 0ec34fd72c, readd rtcInit to boardInit (on AR9X)
2019-11-20 11:56:22 +01:00

494 lines
13 KiB
C++

/*
* Copyright (C) OpenTX
*
* Based on code named
* th9x - http://code.google.com/p/th9x
* er9x - http://code.google.com/p/er9x
* gruvin9x - http://code.google.com/p/gruvin9x
*
* License GPLv2: http://www.gnu.org/licenses/gpl-2.0.html
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include "opentx.h"
#if defined(PCBAR9X)
#include "i2c_driver.h"
#endif
uint16_t ResetReason;
uint32_t Master_frequency ;
volatile uint8_t lcdLock;
volatile uint32_t lcdInputs;
uint16_t Current_analogue;
uint16_t Current_max;
uint32_t Current_accumulator;
uint32_t Current_used;
extern "C" void sam_boot( void ) ;
// Prototype
// Free pins (PA16 is stock buzzer)
// PA23, PA24, PA25, PB7, PB13
// PC20, PC21(labelled 17), PC22, PC24
// REVB
// PA25, use for stock buzzer
// PB14, PB6
// PC21, PC19, PC15 (PPM2 output)
inline void config_free_pins()
{
configure_pins( PIO_PB14, PIN_ENABLE | PIN_INPUT | PIN_PORTB | PIN_PULLUP ) ;
}
// Assumes PMC has already enabled clocks to ports
inline void setup_switches()
{
configure_pins( 0x01808087, PIN_ENABLE | PIN_INPUT | PIN_PORTA | PIN_PULLUP ) ;
configure_pins( 0x00000030, PIN_ENABLE | PIN_INPUT | PIN_PORTB | PIN_PULLUP ) ;
configure_pins( 0x91114900, PIN_ENABLE | PIN_INPUT | PIN_PORTC | PIN_PULLUP ) ;
}
inline void UART3_Configure(uint32_t baudrate, uint32_t masterClock)
{
Uart *pUart = BT_USART;
/* Configure PIO */
configure_pins( (PIO_PB2 | PIO_PB3), PIN_PERIPHERAL | PIN_INPUT | PIN_PER_A | PIN_PORTB | PIN_NO_PULLUP ) ;
/* Configure PMC */
PMC->PMC_PCER0 = 1 << BT_ID;
/* Reset and disable receiver & transmitter */
pUart->UART_CR = UART_CR_RSTRX | UART_CR_RSTTX
| UART_CR_RXDIS | UART_CR_TXDIS;
/* Configure mode */
pUart->UART_MR = 0x800 ; // NORMAL, No Parity
/* Configure baudrate */
/* Asynchronous, no oversampling */
pUart->UART_BRGR = ( (masterClock / baudrate) + 8 ) / 16;
/* Disable PDC channel */
pUart->UART_PTCR = UART_PTCR_RXTDIS | UART_PTCR_TXTDIS;
/* Enable receiver and transmitter */
pUart->UART_CR = UART_CR_RXEN | UART_CR_TXEN;
#if 0
pUart->UART_IER = UART_IER_RXRDY ;
NVIC_EnableIRQ(UART1_IRQn) ;
#endif
}
void UART3_Stop()
{
BT_USART->UART_IDR = UART_IDR_RXRDY ;
NVIC_DisableIRQ(UART1_IRQn) ;
}
// Starts TIMER0 at full speed (MCK/2) for delay timing
// @ 36MHz this is 18MHz
// This was 6 MHz, we may need to slow it to TIMER_CLOCK2 (MCK/8=4.5 MHz)
inline void start_timer0()
{
Tc *ptc ;
// Enable peripheral clock TC0 = bit 23 thru TC5 = bit 28
PMC->PMC_PCER0 |= 0x00800000L ; // Enable peripheral clock to TC0
ptc = TC0 ; // Tc block 0 (TC0-2)
ptc->TC_BCR = 0 ; // No sync
ptc->TC_BMR = 2 ;
ptc->TC_CHANNEL[0].TC_CMR = 0x00008001 ; // Waveform mode MCK/8 for 36MHz osc.
ptc->TC_CHANNEL[0].TC_RC = 0xFFF0 ;
ptc->TC_CHANNEL[0].TC_RA = 0 ;
ptc->TC_CHANNEL[0].TC_CMR = 0x00008040 ; // 0000 0000 0000 0000 1000 0000 0100 0000, stop at regC
ptc->TC_CHANNEL[0].TC_CCR = 5 ; // Enable clock and trigger it (may only need trigger)
}
// TIMER2 at 200Hz, provides 5mS for sound and 10mS tick on interrupt
// Starts TIMER2 at 200Hz, commentd out drive of TIOA2 (A26, EXT2)
inline void start_timer2()
{
Tc *ptc ;
uint32_t timer ;
// Enable peripheral clock TC0 = bit 23 thru TC5 = bit 28
PMC->PMC_PCER0 |= 0x02000000L ; // Enable peripheral clock to TC2
timer = Master_frequency / 12800 / 2; // MCK/128 and 200 Hz
ptc = TC0 ; // Tc block 0 (TC0-2)
ptc->TC_BCR = 0 ; // No sync
ptc->TC_BMR = 0 ;
ptc->TC_CHANNEL[2].TC_CMR = 0x00008000 ; // Waveform mode
ptc->TC_CHANNEL[2].TC_RC = timer ; // 10 Hz
ptc->TC_CHANNEL[2].TC_RA = timer >> 1 ;
ptc->TC_CHANNEL[2].TC_CMR = 0x0009C003 ; // 0000 0000 0000 1001 1100 0000 0000 0011
ptc->TC_CHANNEL[2].TC_CCR = 5 ; // Enable clock and trigger it (may only need trigger)
NVIC_EnableIRQ(TC2_IRQn) ;
TC0->TC_CHANNEL[2].TC_IER = TC_IER0_CPCS ;
}
void interrupt5ms()
{
static uint32_t pre_scale ; // Used to get 10 Hz counter
HAPTIC_HEARTBEAT();
if ( ++pre_scale >= 2 ) {
BUZZER_HEARTBEAT();
pre_scale = 0 ;
per10ms();
}
}
extern "C" void TC2_IRQHandler()
{
uint32_t dummy;
/* Clear status bit to acknowledge interrupt */
dummy = TC0->TC_CHANNEL[2].TC_SR;
(void) dummy ; // Discard value - prevents compiler warning
interrupt5ms();
}
// PWM used for PPM generation, and LED Backlight
// Output pin PB5 not used, PA17 used as PWMH3 peripheral C
// PWM peripheral ID = 31 (0x80000000)
// Ensure PB5 is three state/input, used on REVB for MENU KEY
// Configure PWM3 as PPM drive,
// PWM0 is LED backlight PWM on PWMH0
// This is PC18 peripheral B, Also enable PC22 peripheral B, this is PPM-JACK (PWML3)
//
// REVB board:
// PWML2, output as peripheral C on PA16, is for HAPTIC
// For testing, just drive it out with PWM
// PWML1 for PPM2 output as peripheral B on PC15
// For testing, just drive it out with PWM
void init_pwm()
{
Pwm *pwmptr ;
uint32_t timer ;
PMC->PMC_PCER0 |= ( 1 << ID_PWM ) ; // Enable peripheral clock to PWM
MATRIX->CCFG_SYSIO |= 0x00000020L ; // Disable TDO let PB5 work!
/* Configure PIO */
configure_pins( PIO_PA16, PIN_PERIPHERAL | PIN_INPUT | PIN_PER_C | PIN_PORTA | PIN_NO_PULLUP ) ;
configure_pins( PIO_PC18, PIN_PERIPHERAL | PIN_INPUT | PIN_PER_B | PIN_PORTC | PIN_NO_PULLUP ) ;
configure_pins( PIO_PC22, PIN_PERIPHERAL | PIN_INPUT | PIN_PER_B | PIN_PORTC | PIN_NO_PULLUP ) ;
// Configure clock - depends on MCK frequency
timer = Master_frequency / 2000000 ;
timer |= ( Master_frequency / ( 32* 10000 ) ) << 16 ;
timer &= 0x00FF00FF ;
pwmptr = PWM ;
pwmptr->PWM_CLK = 0x05000000 | timer ; // MCK for DIVA, DIVA = 18 gives 0.5uS clock period @35MHz // MCK/32 / timer = 10000Hz for CLKB
// PWM0 for LED backlight
pwmptr->PWM_CH_NUM[0].PWM_CMR = 0x0000000C ; // CLKB
pwmptr->PWM_CH_NUM[0].PWM_CPDR = 100 ; // Period
pwmptr->PWM_CH_NUM[0].PWM_CPDRUPD = 100 ; // Period
pwmptr->PWM_CH_NUM[0].PWM_CDTY = 40 ; // Duty
pwmptr->PWM_CH_NUM[0].PWM_CDTYUPD = 40 ; // Duty
pwmptr->PWM_ENA = PWM_ENA_CHID0 ; // Enable channel 0
// PWM2 for HAPTIC drive 100Hz test
pwmptr->PWM_CH_NUM[2].PWM_CMR = 0x0000000C ; // CLKB
pwmptr->PWM_CH_NUM[2].PWM_CPDR = 100 ; // Period
pwmptr->PWM_CH_NUM[2].PWM_CPDRUPD = 100 ; // Period
pwmptr->PWM_CH_NUM[2].PWM_CDTY = 40 ; // Duty
pwmptr->PWM_CH_NUM[2].PWM_CDTYUPD = 40 ; // Duty
pwmptr->PWM_OOV &= ~0x00040000 ; // Force low
pwmptr->PWM_OSS = 0x00040000 ; // Force low
// pwmptr->PWM_ENA = PWM_ENA_CHID2 ; // Enable channel 2
}
// LCD i/o pins
// LCD_RES PC27
// LCD_CS1 PC26
// LCD_E PC12
// LCD_RnW PC13
// LCD_A0 PC15
// LCD_D0 PC0
// LCD_D1 PC7
// LCD_D2 PC6
// LCD_D3 PC5
// LCD_D4 PC4
// LCD_D5 PC3
// LCD_D6 PC2
// LCD_D7 PC1
#define LCD_DATA 0x000000FFL
#define LCD_A0 0x00000080L
#define LCD_RnW 0x00002000L
#define LCD_E 0x00001000L
#define LCD_CS1 0x04000000L
#define LCD_RES 0x08000000L
void configure_pins( uint32_t pins, uint16_t config )
{
Pio * pioptr;
pioptr = PIOA + ((config & PIN_PORT_MASK) >> 6);
if (config & PIN_PULLUP) {
pioptr->PIO_PPDDR = pins;
pioptr->PIO_PUER = pins;
}
else {
pioptr->PIO_PUDR = pins;
}
if (config & PIN_PULLDOWN) {
pioptr->PIO_PUDR = pins;
pioptr->PIO_PPDER = pins;
}
else {
pioptr->PIO_PPDDR = pins;
}
if (config & PIN_HIGH) {
pioptr->PIO_SODR = pins;
}
else {
pioptr->PIO_CODR = pins;
}
if (config & PIN_INPUT) {
pioptr->PIO_ODR = pins;
}
else {
pioptr->PIO_OER = pins;
}
if (config & PIN_PERI_MASK_L) {
pioptr->PIO_ABCDSR[0] |= pins;
}
else {
pioptr->PIO_ABCDSR[0] &= ~pins;
}
if (config & PIN_PERI_MASK_H) {
pioptr->PIO_ABCDSR[1] |= pins;
}
else {
pioptr->PIO_ABCDSR[1] &= ~pins;
}
if (config & PIN_ENABLE) {
pioptr->PIO_PER = pins;
}
else {
pioptr->PIO_PDR = pins;
}
}
void opentxBootloader();
// Set up for volume control (TWI0)
// Need PA3 and PA4 set to peripheral A
#if !defined(PCBAR9X)
void i2cInit()
{
Pio *pioptr;
uint32_t timing;
PMC->PMC_PCER0 |= 0x00080000L ; // Enable peripheral clock to TWI0
TWI0->TWI_CR = TWI_CR_SWRST ; // Reset in case we are restarting
/* Configure PIO */
pioptr = PIOA ;
pioptr->PIO_ABCDSR[0] &= ~0x00000018 ; // Peripheral A
pioptr->PIO_ABCDSR[1] &= ~0x00000018 ; // Peripheral A
pioptr->PIO_PDR = 0x00000018 ; // Assign to peripheral
timing = Master_frequency * 5 / 1000000 ; // 5uS high and low
timing += 15 - 4 ;
timing /= 16 ;
timing |= timing << 8 ;
TWI0->TWI_CWGR = 0x00040000 | timing ; // TWI clock set
TWI0->TWI_CR = TWI_CR_MSEN | TWI_CR_SVDIS ; // Master mode enable
TWI0->TWI_MMR = 0x002F0000 ; // Device 5E (>>1) and master is writing
NVIC_EnableIRQ(TWI0_IRQn) ;
}
#endif
void boardInit()
{
Pio *pioptr ;
ResetReason = RSTC->RSTC_SR;
MATRIX->CCFG_SYSIO |= 0x000000F0L ; // Disable syspins, enable B4,5,6,7
PMC->PMC_PCER0 = (1<<ID_PIOC)|(1<<ID_PIOB)|(1<<ID_PIOA)|(1<<ID_UART0) ; // Enable clocks to PIOB and PIOA and PIOC and UART0
PIOC->PIO_PER = PIO_PC25 ; // Enable bit C25 (USB-detect)
pwrInit() ;
config_free_pins() ;
// Next section configures the key inputs on the LCD data
pioptr = PIOC;
pioptr->PIO_PER = 0x0000003BL ; // Enable bits 1,3,4,5, 0
pioptr->PIO_OER = PIO_PC0 ; // Set bit 0 output
pioptr->PIO_ODR = 0x0000003AL ; // Set bits 1, 3, 4, 5 input
pioptr->PIO_PUER = 0x0000003AL ; // Set bits 1, 3, 4, 5 with pullups
pioptr = PIOB ;
pioptr->PIO_PUER = PIO_PB5 ; // Enable pullup on bit B5 (MENU)
pioptr->PIO_PER = PIO_PB5 ; // Enable bit B5
setup_switches() ;
// Enable PCK2 on PB3, This is for testing of Timer 2 working
// It will be used as serial data to the Bluetooth module
pioptr->PIO_ABCDSR[0] |= PIO_PB3 ; // Peripheral B
pioptr->PIO_ABCDSR[1] &= ~PIO_PB3 ; // Peripheral B
pioptr->PIO_PDR = PIO_PB3 ; // Assign to peripheral
PMC->PMC_SCER |= 0x0400 ; // PCK2 enabled
PMC->PMC_PCK[2] = 2 ; // PCK2 is PLLA
start_timer2() ;
start_timer0() ;
adcInit() ;
init_pwm() ;
__enable_irq();
audioInit();
i2cInit();
eepromInit();
#if defined(ROTARY_ENCODER_NAVIGATION)
rotaryEncoderInit();
#endif
lcdInit();
init_SDcard();
#if defined(PCBAR9X)
rtcInit();
#endif
}
uint8_t temperature = 0; // Raw temp reading
uint8_t maxTemperature = 0 ; // Raw temp reading
void end_bt_tx_interrupt()
{
Uart *pUart = BT_USART ;
pUart->UART_IDR = UART_IDR_TXBUFE ;
NVIC_DisableIRQ(UART1_IRQn) ;
}
uint16_t getCurrent()
{
static uint16_t Current ;
static uint32_t Current_sum ;
static uint8_t Current_count ;
Current_sum += anaIn(TX_CURRENT);
if (++Current_count >= 50) {
Current = Current_sum / 5 ;
Current_sum = 0 ;
Current_count = 0 ;
}
uint32_t current_scale = 488 + g_eeGeneral.txCurrentCalibration ;
return (current_scale * Current) / 8192;
}
#define STICK_LV_GAIN 0x01
#define STICK_LH_GAIN 0x02
#define STICK_RV_GAIN 0x04
#define STICK_RH_GAIN 0x08
#define GAIN_LV 0x00080000
#define GAIN_LH 0x00000020
#define GAIN_RV 0x20000000
#define GAIN_RH 0x00000008
#define OFF_LV 0x00000200
#define OFF_LH 0x00000004
#define OFF_RV 0x00004000
#define OFF_RH 0x00000002
void setSticksGain(uint8_t gains)
{
Adc *padc ;
uint32_t gain ;
uint32_t offset ;
gain = 0 ;
offset = 0 ;
padc = ADC ;
if ( gains & STICK_LV_GAIN ) {
gain |= GAIN_LV ;
offset |= OFF_LV ;
}
if ( gains & STICK_LH_GAIN ) {
gain |= GAIN_LH ;
offset |= OFF_LH ;
}
if ( gains & STICK_RV_GAIN ) {
gain |= GAIN_RV ;
offset |= OFF_RV ;
}
if ( gains & STICK_RH_GAIN ) {
gain |= GAIN_RH ;
offset |= OFF_RH ;
}
padc->ADC_CGR = gain;
padc->ADC_COR = offset;
}
void calcConsumption()
{
Current_accumulator += Current_analogue ;
static uint32_t OneSecTimer;
if (++OneSecTimer >= 100) {
OneSecTimer -= 100 ;
Current_used += Current_accumulator / 100 ; // milliAmpSeconds (but scaled)
Current_accumulator = 0 ;
}
}
uint16_t getBatteryVoltage()
{
int32_t instant_vbat = anaIn(TX_VOLTAGE); // using filtered ADC value on purpose
instant_vbat = (instant_vbat + instant_vbat*(g_eeGeneral.txVoltageCalibration)/128) * 4191;
instant_vbat /= 5530;
return (uint16_t)instant_vbat;
}
void boardOff()
{
pwrOff();
}