Dahua-OEM 2 MP camera. The SC223A is on hardware I2C0 routed to the
VI-RAW pads (0x112c0060/0x64 func2) rather than the default mipi-sensor
pads (0x30/0x34 func1) the SDK probes, and needs a 27 MHz MCLK
(0x120100f0=0x19; SDK default 0x11/div4 leaves it unresponsive).
S71devmem re-muxes the pads, selects the SENSOR_RSTN reset (GPIO8_7
func2) and fixes MCLK after S70vendor/load_goke; the stock
open_sensor_i2c then reaches the sensor over /dev/i2c-0. No kernel
module needed.
Verified on hardware: chip-id 0xcb3e over HW I2C0, MIPI lock 1920x1080
zero errors, majestic streams correct colour 1080p.
Co-authored-by: build <build@local>
Co-authored-by: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* Add TP-Link Kasa KC110 (HI3518EV200 + OV2735)
New device variant: hi3518ev200_ultimate_tplink-kasa-kc110.
Contents:
- kc110-board-support package: PTZ binary (mmap'd PL061), gpio-motors
shim for the openipc web GUI, IR control script, and a boot-time
pinmux init that writes 0x1 to the chip7/chip8 pads (0x200f00e8/ec/
f0/fc/100/104). The OpenIPC kernel pinctrl driver does not auto-set
these for the KC110's pan motor / IR-cut / IR-LED pads — the vendor
firmware writes them explicitly in hn_config.sh. Without this,
PL061 GPIODATA writes succeed silently but the pads never drive
the ULN2803 / solenoid / LED.
- Device overlay:
* etc/sensors/ov2735_i2c_1080p.ini — input_mode=0 (MIPI), 1-lane
(was input_mode=4 / 4-lane in upstream cv200 osdrv, which is
wrong for OV2735).
* usr/bin/load_hisilicon — adds an "ov2735" case that mirrors
ov2710_mipi (same MIPI pinmux + clock).
* usr/share/openipc/customizer.sh — first-boot configuration:
RTL8188FU wlandev, sensor config path, IR-cut pin 64, backlight
pin 63, lightMonitor true (AE recovery after IR-cut toggle).
- README.md row.
Hardware notes:
- SoC: Hi3518EV200; Sensor: OV2735 (MIPI 1-lane, RAW10);
Wi-Fi: RTL8188FU (USB); Flash: W25Q128 16 MB NOR.
- PTZ: 4-phase unipolar steppers via ULN2803 darlington array.
Pan = vendor base-10 GPIO 81/74/73/72 = OpenIPC PL061 65/60/59/58;
tilt = 0/1/2/44 = 0/1/2/36 (vendor's "44" is bank 4 pin 4 — i.e.
pin 36 in OpenIPC's PL061 numbering, NOT 44).
- IR-cut filter: GPIO 64 (vendor 80) active-low; IR-LED: GPIO 63
(vendor 77).
Status: PTZ + GPIO + IR fully functional. Video pipeline currently
needs an LD_PRELOAD shim around HI_MIPI_SET_DEV_ATTR because upstream
majestic builds combo_dev_attr_t with enIntfMode=DC / raw_data_type=0
for MIPI sensors that need RAW10. The shim is downstream-only pending
a real fix to majestic upstream; this PR delivers the rest of the
KC110 board support and will produce a fully-functional camera once
the majestic fix lands.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
* tplink-kasa-kc110: use ov2735_mipi_1080p.ini
Follow OpenIPC/firmware #2155, which ships the OV2735 MIPI config as a
separate ov2735_mipi_1080p.ini and leaves ov2735_i2c_1080p.ini (the
parallel/DVP config) untouched.
- Rename the device's bundled sensor .ini to ov2735_mipi_1080p.ini and
carry the full corrected MIPI config: input_mode=0 (MIPI),
data_type=2 (RAW10), lane_id 2-lane, Input_mod=5 (MIPI),
Mask_0=0xFFF00000. The previous bundled copy only had input_mode
fixed (data_type/Input_mod/Mask_0 were still the wrong DVP defaults).
- Point customizer.sh's isp.sensorConfig at the new file.
- Exclude the unused parallel ov2735_i2c_1080p.ini from the image.
Verified on a TP-Link Kasa KC110 (OV2735 2-lane MIPI RAW10): clean
image, correct AE, RTSP H.264 1080p.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
---------
Co-authored-by: moontwister <moontwister@users.noreply.github.com>
Co-authored-by: Claude Opus 4.7 <noreply@anthropic.com>
OpenIPC/firmware PR #2162 (merged 2026-05-30) dropped the legacy
BR2_TOOLCHAIN_EXTERNAL_GCC_8=y + BR2_GCC_VERSION_LEGACY=y block from
its 18 ARM defconfigs and ships gcc 13.3.0 to those platforms now.
OpenIPC/builder's per-device and common Goke defconfigs still pinned
gcc 8, so every Goke job in the 2026-06-02 nightly Build run failed at
the toolchain stage with:
Incorrect selection of gcc version: expected 8.x, got 13.3.0
make[1]: *** [toolchain-external-custom/.stamp_configured] Error 1
Mirror #2162 across the 24 affected defconfigs (8 common + 16
per-device). No other defconfig content changes.
Unrelated 4 Sigmastar rootfs-overflow failures in the same nightly are
tracked separately.
Fixes failing run: https://github.com/OpenIPC/builder/actions/runs/26804792607
Co-authored-by: John <zekccsripfwrocp-15689@yn.furvionx.com>
Co-authored-by: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
OpenIPC/firmware PR #2090 (2026-05-13, "IMX335 companion to
openhisilicon #99") renamed `general/package/goke-osdrv-gk7205v200/
files/sensor/config/60fps/` to `high-fps/`. The xg521 device-specific
goke-osdrv-gk7205v200.mk override here still references the old path,
causing every cron build of gk7202v300_lite_xg521 to fail:
/usr/bin/install: cannot stat 'general/package/goke-osdrv-gk7205v200//
files/sensor/config/60fps/*.ini': No such file or directory
Update the two install lines to use `high-fps` matching the renamed
upstream directory. Target install path also moves from
/etc/sensors/60fps → /etc/sensors/high-fps for consistency with what
the rest of the V4 sensor presets use.
The matching exclude-list entry in
devices/gk7202v300_lite_xg521/general/scripts/excludes/gk7202v300_lite.list
references /etc/sensors/60fps/... and is now stale; left as-is since
`rm -f` on a non-existent path is a no-op (rootfs_script.sh:
xargs -I % rm -f ${TARGET_DIR}%). Can be cleaned in a follow-up.
Other Goke device overlays (gk7205v200_lite_*, gk7205v210_lite_*,
gk7205v300_lite_*) only have the same exclude-list staleness and no
broken install rule, so they aren't affected by this bug.
Co-authored-by: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Add BR2_PACKAGE_HISILICON_OPENSDK=y to 9 hi3516cv200-family profiles
that were missing it. These boards will now get open_ modules built
from openhisilicon source instead of vendor-only blobs from osdrv.
Co-authored-by: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
